RFP's - Firehouse Forums - Firefighting Discussion
RFP's - Firehouse Forums - Firefighting Discussion:
From Firehouse.com forums thought this was a great RFP list that anyone could dream up...
'Here are 4 rfp's we sent out for 11 new vehicles. They led to complete spec submissions by apparatus vendors and led to an order for 5.7 million".
Boosters
Cab and Chassis
*chassis with 42,000 lbs 6 x 6 chassis option
*13,000 mile cross country MTBF test
*Seating for 4
*XXXX model vehicle fixed radio and antenna with three David Clark radio headsets with intercom and radio push to talk buttons and one XXXXX model portable radios one with a dual ear David Clark headset for the engineer, dual chargers for spare battery and radio
*Reflective vehicle number plaques in drop in mounts on four sides
*Reflective department name on four sides
*Brush guards over cab face and skid plates where needed
*Central winch that operates front or rear.
*Single point fluid and maintenance area
*400+ mile range on a load of fuel
*All the time four wheel drive with central tire inflation with push button control
*Ability to ford 60 inches of water, climb a 60% grade, 21 inch ground clearance, climb a 24 inch wall, handle a 30% side hill,
*Cat Diesel engine 300 hp with 850 lbs torque with exhaust brake
*Rear vision camera with monitor and with back talk system
*Custom apparatus manuals
*200 amp alternator
*10KW AMPS XL units generator with 90% capacity at idle, in cab switches, soft start ptos no exception, with fulltime pto’s, one 2000 watt Fire Research Focus flood light front, rear, left and right.
*Anti lock brakes
*7 speed automatic transmission with push button control
*Spare tire
*Kussmaul pump plus 1200 with auto eject
*Air conditioning
*One Grace vehicle transmitter
*3 Responder lights with chargers,
*Night vision blue lighting in cab
*Brackets in cab for three breathing apparatus
*Cab controls to include pump start, deck gun charge, outlet gauge, all CAF controls, discharges, mini MC water and foam level gauge, generator and flood light controls
*Letter and stripe to FD requirements
*Night vision blue lighting in cab
Fire Body
*Aluminum fire body loaded on double frame flat bed at 4% angle to the rear
* 1200 gallon water tank with integral 50 gallon Class A tank, hose beds and dunnage area
*Dual side dumps and power chute extensions at rear of vehicle with remote controls in cab
* 500 gpm/200 cu ft CAF system plumbed to Elkhart gun and 2 ½” discharge. Note: pump module shall be a second piece from tank module connected together with Class1 hose to allow both to move independently.
*Provide oil less primer
*Provide thermal relief valve and alarm
*3 inch tank to pump and 2 1/2” tank filler
*System to default to CAFs
*Foam Pro 1600 system foam on when pump is on
*Solenoid style CAFS controls with 2 inch or 2 ½” Akron valve slaved to air discharges to control wet, dry or air off via single front and rear air switch. No air valves, cubic foot meters, etc
*200 foot 1 ¾” preconnect complete with 200 feet of High Combat hose
*500 foot bed of 1” hose complete with hose
*One 2 ½” ungated discharge mounted as low as possible near the attack line beds to supply supplied Akron water thief to supply both attack beds with the 2 ½” port reduced to 1 ½” for a supplied 1 ½” by 1” gated wye to supply the 1 inch bed
*Two 2 ½” suctions one with a 20 foot 3 inch squirrel tail suction preconnect with low lift foot valve strainer
*Full width dunnage area with lid with dual fold down ladders for access
*Elkhart Sidewinder on cab roof with CAF tip controlled from cab with joy stick tether on cord long enough with velcro mounts for driver and officer use, with spot light mounted on gun
*Two 1” Iowa Fallon tip pistol grip nozzles with TFT break apart mid force tips and triple stacked tips
*One 1 ½” Iowa Fallon tip pistol grip nozzles with TFT break apart mid force tip and triple stacked tips
*25 feet 1 ¾” hose in donut rack and strap stored preconnected to 2 ½” suction connection with a 2 ½” male to 1 ½” female adapter and a 1 ½” male to 2 ½” long handle swivel adapter
*50 feet of 2 ½” hose in donut roll holder and strap with 2 ½” Akron hydrant valve
*One 5/8 inch Fire Hooks Unlimited fiber glass bolt cutter
*Dual Akron fitzsall and hydrant wrench mount
*Four roof mounted 6 inch diameter four color strobe lights to indicate water level.
*Roof mounted remote control thermal imager/color TV with quadruple head up flat panel displays and quintuple recorders with auto on via parking brake and dual 6 switch option for viewing handheld imagers, vehicle TV and imager and backup camera.
*Minimal warning light and siren package, wig wag head lights,
*Four Scotty 1 gallon garden hose Barricade gel packs
*Two 5 gallon pails of Barricade gel
*Two pointed shovels and two rubbish hooks with fiber glass handles
*Mount all listed loose equipment
*Reflective vehicle number plaques in drop in mounts on four sides
All Kochek laser etched hose fittings and sequentially numbered and hose fitting colors shall be white, purple, and gray.
*One foam can wrench
*One spare 20 foot 3 inch hard suction tube
*All strainers and suction couplings color coded as well
Warrantee
*The vendor will guarantee the lease rate at time of the order with lease to start at time of delivery. with lease to start at time of delivery.
*All apparatus to meet NFPA except where noted.
*Paint 10 years, body structure and cab 10 years, life time tank stainless body 15 years, stainless plumbing 10 years engine drive train 5 years, foam system, lifetime frame, 2 years, nozzles 5 years, hose 10 years, and pumps 5 years. Trips 4 per truck for 3 members. Provide 15% contingency money.
Tender Hose Wagons
Cab and Chassis
*4 door chassis with 7 SCBA seat backs
*500 hp ISM engine with exhaust brake ands automatic transmission
*Air conditioning, describe exact air conditioning system proposed
*Remote control west coast mirrors with fisheyes
*10 inch front look down mirror
*In cab overhead panel to control (side dumps and chutes, Fire Research all in one combo governor instruments and pressure gauge unit, mini MC water and two foam level gauges, Akron deck gun control and remote tether mounted with velcro, Akron electric valve for gun, spot light switch for gun, Fire Pro foam control head to default in foam when pump is engaged, pump and generator engagement switch, front, rear, officer and drivers floodlight switch),
*Only two switches to control, siren and emergency lights,
*No head light switch,
*Ground illumination via parking brake, 12 lights
*No gauges except speedometer and fuel gauge,
*Bell and Alarm, repeater for Grace and vehicle transponder,
*Truck horn and red light system warnings connected to all visual and audible alarms on the vehicle,
*Bullard handheld imager vehicle charger with spare battery charger
*6 batteries Delco model 1150
*Kussmaul pump plus 1200 system with auto eject
*Car type starter switch
*Headlight off on parking brake
*LED lights everywhere possible,
*7 Responder lights with chargers,
*XXXX model vehicle fixed radio and antenna and two XXXXX model portable radios one with a dual ear david clark headset for the engineer, dual chargers for spare battery and radio
*Water level on/off switch,
*One quarter inch armored wheel wells front and rear and compartment undersides to protect agains blown tires
*AM FM stereo with cassette player and four speakers,
*Triple frame rail,
*290 amp alternator,
*Night vision blue lighting in cab
*One Grace vehicle transmitter
Pump
*2000 gpm Waterous Eclipse with 500 gpm hot shift pto pump for pump and roll, with shared discharge manifold.
*Pressure relief valve
*Front and rear 3 inch discharge to feed with an Akron water thief on both discharges,
*Remote control Akron deck gun with 4 inch water supply with Collins FX-12 spot light mounted on gun and automatic fog tip plus tether remote on pump panel
*Officer side 5” LDH discharge with 5 inch by 2 ½” adapter and attached water thief,
*Garden hose wye and spigot
*6” side suctions with Akron piston intake valve attached to each one,
*5” storz squirrel tail side suction on each side, with wafer valves, Elkhart 5” chicksan swivels, attached to fifteen feet of 5” suction hose on one side and 3” suction hose on the other with storz coupling with Kochek foot valve low lift strainers with jets color coded to match the rigs color scheme, pull drains on each suction connection, triple primer control handles on each side to allow drafting from main pump, squirrel tail or side suction. Suction hose to be wrapped around the pump panel.
*No check valve from 4” tank to pump and 3 inch tank fill,
*All stainless steel piping,
*Auto drains as needed,
*Electric tank filler, tank to pump control on each pump panel
*Thermal relief valves with light and alarm
*Oil less primer
Fire Body
*100 inch wide body, maximum compartments available on apparatus by manufacturer.
*26 inch deep compartments Katy style with Zico overhead rack on both sides, standard doors everywhere except two front compartments that include the pump panel rollup doors and full height compartments in front of ground ladder and drop tank racks
*Raise rear body 6 inches behind rear wheels
*Ground ladders 35’ and 14’ and 10’ folding on Zico drop down rack, good Purlon halyard rope,
*Stainless or aluminum side dumps and power extensions 12 inch with cover flaps and with remote electric extension and valves controls in cab located between the wheel wells
*Saulsbury custom manuals
*An extra 20 foot length of 3 and 5” on Zico rack on each side,
*200 foot 3” bomb line in round bottom donut holder on officer side panel complete with TFT mini monitor with 150 to 500 gpm TFT fog tip,
*One 200 foot 1 inch preconnected line in donut roll holder with round bottom on officer’s side pump panel.
*Two 200 foot 1 ¾” labeled 2” precons on bumper round bottom,
*Two 300 foot 1 ¾” labeled 2” preconnects in donut roll holders round bottom located recessed into the rear of the apparatus with room between them for a Meyers Quick drop.
*2500 feet 5 inch split bed with diamond plate hose bed cover with assists and locks to hold open
*3500 total liquid tank,
*101 gallon Class A tank complete with Ansul foam,
*99 gallon Class B tank complete with XXX foam.
*Mount all loose equipment to department desires using pullout drop down trays, pullout shelves and tool boards
*Rear vision camera and monitor mounted on A post in cab, with back talk system
*25Kw AMPs fulltime PTO generator with soft start with 90% capacity at idle in cab switches, two forward 2000 watt Fire Research Focus, two 2000 watt Tele Lite each side and two 2000 watt Fire Research Focus rear.
*1 cord light with 750 watt lights with Tele Lite base and Havis Shield head with on/off switch on the light head and 110 outlet on the front bumper attached to a manual rewind cord reel stored in dunnage area with 200 feet of cord run to the front bumper with the cord fed under the unit in tube to the bumper, reels to be attached to the generator
*2 cord lights with 750 watt lights Tele Lite base and Havis Shield head with on/off on head and outlet stored on the pump panel connected to manual rewind cord reels with 200 feet of cord in stored in the dunnage area with feed to the pump panel, reels to be attached to the generator, 3 prong 15 amp connectors on all electrical.
*Dunnage area storage for two 200 foot 110 volt reels connected to supply a pair of 1000 watt side of cab mounted tripods lights with outlet on light heads and on/off switch on head
*AMPs generator and cord reels in dunnage area. Two 200 foot hydraulic reels in dunnage area connected to a 220 volt dual hydraulic pump tubed under the rig to the front bumper to supply the extrication tool with air operated on/off for each diverter valve.
*Two sets 4 water level lights 7 x 11” LED Wheelens in four colors,
*Pool ladder to access the hose bed located at the rear of the truck,
*Rear Houston style Scotchlite,
*Wheel wells both side shall contain 12 SCBA bottles no holders,
*4 SCBA mounted in over wheel compartment,
*No rear compartments
*Special Scotchlite graphics package
*Reflective vehicle number plaques in drop in mounts on four sides
*Reflective department name on four sides
*New Scotchlite striping single peace no layered type allowed on stripe
Loose equipment
*One Carlin valve 5” storz by 5” storz,
*Six 1 ½” Iowa Fallon tip pistol grip nozzles with TFT break apart mid force tip dual pressure and triple stacked tips
*One 1” Iowa Fallon tip pistol grip nozzles with TFT break apart mid force tip dual pressure and triple stacked tips
*Two 1 ½” MX tips,
*Two 1” MX tips,
*6 foot Superior Flamefighter piercing nozzle with shutoff and two 3 foot extension pipe
*14 spare 30 minute Scott Kevlar bottles
*7 Scott 50 air packs with 30 minute Kevlar bottles and integrated PASS
*6 salvage covers to match colors (to all be blue, green and orange, one color per vehicle)
*One Hebert 5” hose clamp
*One 2 ½” screw type hydrant gate valve
*One burst hose jacket leather 2 ½” Darley
*Two misting Super Vac smoke ejectors with wheels and pull handle
*One Akron hose roller
*Two Partner 650 saws with Fire Hooks Unlimited strap, Chopper blade and Da Ax Blade, and spare fuel can for each saw. One spare each blade.
*One foam can wrench
*Cordless DeWalt drill with Iowa S hook lock puller, Garage hook, Key tool set and 3/8 inch Titanium drill bit.
*One each Iowa American Rattlesnake ends polished stainless heads 6, 8, and 12 foot
*One 8 lb Force axe and pick head axe with polished stainless heads
*One 5/8 inch Fire Hooks Unlimited fiber glass bolt cutter
*One Iowa American halligan with strap loop, marry strap and Iowa
*American over the shoulder strap
*One 2 ½ gallon water extinguisher with Iowa American strap
*Ansul K20E cartridge dry chemical extinguisher
All fittings to be colored(Blue for one rig, red for another, green, orange, black and yellow Kochek laser etched County RFPD #1
*Four 1 1/2 inch NST female to 1 inch NST male adapters
fittings list
*Two 2 ½” female NST to 1 ½” NST male
*Two 2 ½” male to 1 ½” NST female LH swivel
*Two 1 ½” NST make plugs with chains
*Twelve garden hose male by 1” female adapters
*Two 5” storz to 2 ½” LH NST swivel adapters
*Five inch storz by 4 inch storz adapter
*25 gallons spare Class A Ansul foam
*Two Christi hydrant adapters to 5 inch storz
*Two 4 ½”??? hydrant adapters to 5 inch storz
*Two 2 ½” NST Male to 5” Storz fittings
*Two 2 ½” NST female to 5” Storz fittings
*Eleven 100 foot sections of 5” Lime Green and 11 sections of Orange 5 inch hose 100’ with three stencils each section to read at the middle and 25 foot marks plus one each yellow 25’ and 50’ sections of 5 inch hose. All fittings to be colored(Blue for one rig, red for another, green, orange, black and yellow Kochek laser etched and sequentially numbered 1 though all the 5” hose in the department.
*All strainers and suction couplings color coded as well
*Four each 5 inch storz draft gaskets, 5” storz hose gaskets, gasket for fitting, 3 inch storz draft gaskets, 2 ½”, 1 ½” and 1” hose gaskets.
*600 feet of 1 “ hose with 1” NST couplings All fittings to be colored(Blue for one rig, red for another, green, orange, black and yellow Kochek laser etched and sequentially numbered 1 though all
*High Combat 1 ¾” labeled 2” with reflective stripe 200’ yellow, 200’ green, 300’ blue, 300’ orange. All fittings to be colored(blue for one rig, red for another, green, orange, black and yellow Kochek laser etched and sequentially numbered 1 though all
*High Combat hose 200’ green 2 ½” hose, all fittings to be colored(blue for one rig, red for another, green, orange, black and yellow Kochek laser etched and sequentially numbered 1 though all
*25 feet of 2 ½” hose
*Color coded everything plus stick on reflective labels with white letter and vehicle color background labels “ phone number,
*Four Scotty 1 gallon garden hose Barricade gel packs
*Two 5 gallon pails of Barricade gel
*One Craftsman tool box with $400 worth of tools,
*10 lbs Iowa American sledge hammer
*Two long ratchet style hydrant wrenches,
*Mount Akron fitzall and hydrant wrenches on all four sides,
*One 5000 gallon drop tank no-frame style with dual 5” storz fittings and caps.
Warrantee
*The vendor will guarantee the lease rate at time of the order with lease to start at time of delivery..
*All apparatus to meet NFPA except where noted.
*Paint 10 years, body structure and cab 10 years, life time tank stainless body 15 years, stainless plumbing 10 years engine drive train 5 years, foam system, lifetime frame, 2 years, nozzles 5 years, hose 10 years, and pumps 5 years. Trips 4 per truck for 3 members. Provide 15% contingency money.
Tanker Pumpers/Rescues
Cab and Chassis
*E-One Cyclone 8 man command cab with 7 SCBA seats, one air pack mounted between officer and rear seat for driver, 1 seat missing for rehab area. Loose one side window on each side to mount water level lights
*One full width aluminum 80” x 16” by 16” ambulance style storage in place of forward elevated windows and ambulance style sliding glass door, adjustable shelving and compartment above forward facing SCBA seats, 12 gallons of drinking water container with exterior fill and interior and exterior spigot, cup holder, 5 syrup soda dispenser gun type with syrup and carbon dioxide bottle coupled to drinking water, microwave oven, coffee maker, tea maker, refrigerator with ice maker, 110 shore line with automatic change over to AMPs generator, fill rehab area with $500 set aside no charge option to fire district This option was provided at No Charge.
* The vehicle chassis will be manufactured by the body builder.
*500 hp ISM engine with exhaust brake ands automatic transmission
*10 inch front look down mirror
*Air conditioning, describe exact air conditioning system proposed
*Car type starter switch
*In cab overhead panel to control (side dumps and chutes, Fire Research all in one combo governor instruments and pressure gauge unit, mini MC water and two foam level gauges, Akron deck gun control and remote tether mounted with velcro, Akron electric valve for gun, Elkhart deck gun controls and remote tethers mounted with velcro, spot light switch for guns, Fire Pro foam control head to default in foam when pump is engaged, pump and generator engagement switch, front, rear, officer and drivers floodlight switch), compressor switch and wet/dry switches
*Only two switches to control, siren and emergency lights,
*No head light switch,
*Ground illumination via parking brake, 12 lights
*No gauges except speedometer and fuel gauge,
*Bell and Alarm, repeater for Grace and vehicle transponder,
*Truck horn and red light system warnings connected to all visual and audible alarms on the vehicle
*6 batteries Delco model 1150
*Kussmaul pump plus 1200 with auto eject
*Headlight off on parking brake
*LED lights everywhere possible,
*7 Responder lights with chargers,
*Roof top thermal imager with dual head up displays with switching to allow either display to view the roof top imager or one handheld imager and one roof top imager or any two Bullard imagers with up to four channel worth of choices.
*XXXX model vehicle fixed radio and antenna and two XXXXX model portable radios one with a dual ear David Clark headset for the engineer, dual chargers for spare battery and radio
*Water level on/off switch,
*One quarter inch armored wheel wells front and rear and compartment undersides to protect against blown tires
*AM FM stereo with cassette player and four speakers,
*Triple frame rail,
*290 amp alternator,
*Parts book style swiveling map book holder
*One mounted Grace GEMs system with 17 transmitters, repeater, vehicle unit transmitter, 5 extra antennas, colored straps to match the unit and one command receiver, one spare battery, one portable repeater.
*Night vision blue lighting in cab
*Rear vision camera and monitor mounted on A post in cab, with back talk system
Pump
*2000 gpm Waterous Eclipse with 500 gpm hot shift pto pump for pump and roll, with shared discharge manifold.
*CAFS default on solenoid style CAFS controls with 3” Akron valve slaved to air discharges to control wet, dry or air off via single front and rear air switch. CAFs to deck gun, and front and rear 3 inch supply line. No air valves, cubic foot meters, etc
*Front and rear 3 inch discharge to feed with an Akron water thief on both discharges,
*Officer side 5” LDH discharge with 5 inch by 2 ½” adapter and attached water thief,
*Side access 4” tank to pump without check valve, and 3” tank filler valve
*Garden hose wye and spigot
*Pressure relief valve
*6” side suctions with Akron piston intake valve attached to each one,
*5” storz squirrel tail side suction on each side, with wafer valves, Elkhart 5” chicksan swivels, attached to fifteen feet of 5” suction hose on one side and 3” suction hose on the other with storz coupling with Kochek foot valve low lift strainers with jets color coded to match the rigs color scheme, pull drains on each suction connection, triple primer control handles on each side to allow drafting from main pump, squirrel tail or side suction. Suction hose to be wrapped around the pump panel.
*No check valve from 4 inch tank to pump and 3 inch tank fill,
*Two Elkhart Sidewinder monitors, one located on each corner of the front bumper with CAFs tips and Collins FX-12 spot lights mounted on each gun
*All stainless steel piping,
*Auto drains as needed,
*Electric tank filler, tank to pump control on each pump panel
*Thermal relief valves with light and alarm
*Oil less primer
Fire Body
*100 inch wide body, maximum compartments available on apparatus by manufacturer.
*26 inch deep compartments Katy style with Zico overhead rack on both sides, standard doors everywhere except two front compartments that include the pump panel rollup doors and full height compartments in front of ground ladder and drop tank racks
*Raise rear body 6 inches behind rear wheels
*2500 gallons poly tank total wet tank,
*101 gallon Class A tank complete with Ansul foam,
*99 gallon Class B tank complete with XXX foam.
*2500 feet of 5 inch hose split bed with diamond plate hose bed cover with assists and locks to hold open,
*Ground ladders, 35’ 3 fly and 24 foot on one rack and a 24’ and 14’, 10’ and 14 A frame on another Zico drop down rack, Purlon halyard rope,
*Stainless or aluminum side dumps and power extensions 12 inch with cover flaps and with remote electric extension and valves controls in cab located between the wheel wells
*Saulsbury custom manuals
*An extra 20 foot length of 3 and 5” high side compartment
*200 foot 3” bomb line in round bottom donut holder on officer side panel complete with TFT mini monitor with 150 to 500 gpm TFT fog tip,
*One 200 foot 1 inch preconnected line in donut roll holder with round bottom on officer’s side pump panel.
*Two 200 foot 1 ¾” labeled 2” precons on bumper round bottom,
*Two 300 foot 1 ¾” labeled 2” preconnects in donut roll holders round bottom located recessed into the rear of the apparatus with room between them for a Meyers Quick drop.
*1 remote Akron deck gun with 2” CAFs supply and 4 inch water supply with Collins FX-12 spot light mounted gun and an automatic fog tip plus tether remote on pump panel
*Dual AMPS XL units, one 25KW and one 20KW shared shaft pto generators with 90% capacity at idle in cab switches, soft start ptos no exception, with fulltime PTO’s, two forward 2000 watt Fire Research Focus, two 2000 watt Tele Lite each side and two 2000 watt Fire Research Focus rear, Wil Burt 12,000 watt night scan mast.
*Dunnage storage for seven 200 foot 110 volt reels connected to supply a pair of 1000 watt side of cab mounted tripods lights with outlet on light heads and on/off switch on head and a pair of DeWalt sawzalls with Lennox blade and two 200 foot air reels connected a Maxi Force air bag regulator with two 20 ton air bags with on/offs and chains to carry them.
*1 cord light with 750 watt lights with Tele Lite base and Havis Shield head with on/off switch on the light head and 110 outlet on the front bumper attached to a manual rewind cord reel stored in dunnage area with 200 feet of cord run to the front bumper with the cord fed under the unit in tube to the bumper, reels to be attached to the generator
*2 cord lights with 750 watt lights Tele Lite base and Havis Shield head with on/off on head and outlet stored on the pump panel connected to manual rewind cord reels with 200 feet of cord in stored in the dunnage area with feed to the pump panel, reels to be attached to the generator, 3 prong 15 amp connectors on all electrical.
*Two 200 foot hydraulic reels in dunnage area connected to a 220 volt dual hydraulic pump tubed under the rig to the front bumper to supply the extrication tool with air operated on/off for each diverter valve.
*Mount all loose equipment to department desires using pullout drop down trays, pullout shelves and tool boards
*Two sets 4 water level lights 7 x 11” LED Wheelens in four colors,
*Rear Wheelen LEDs in cast bezel everywhere,
*Pool ladder to access the hose bed located at the rear of the truck,
*Rear Houston style Scotchlite,
*Wheel wells both side shall contain 12 SCBA bottles no holders,
*No rear compartments
*Reflective vehicle number plaques in drop in mounts on four sides
*Reflective department name on four sides
*New Scotchlite striping single peace no layered type allowed on stripe
*Bumper mounted Genesis spreader and cutter,
*3 or 4 bottle cascade and Sierra booster in dunnage area with two bottle fill station in compartment
*Bullard handheld imager with 4 channel transmitter 3 colors, with in vehicle charger and spare battery
*Provide wheeled cart complete with a full set of Genesis rams, a Genesis multi-tool, chains and tips, a gas powered simul-pump and two 32 foot hoses with drop down ramp to remove cart,
*Provide wheeled cart complete with a Iowa American pedal cutter, wedgie and rabbit tool plus a 4 ton portapower set with mini ram, fire blanket, chain comealong and connector chain set, air bottle impact wrench and sockets, and windshield tool
*Provide wheeled cart complete with plastic cribbing, wedges and step chocks 100 pieces on cart with drop down ramp,
*Two Maxi Force 20 ton air bags with shutoffs and carry chains
*Provide wheeled cart complete with salvage covers, stapler, roll of plastic and two smoke ejectors
*Receiver hitch style 12 volt winch with power plug in and hitches on the front and rear of the vehicle
Loose equipment
*One Carlin valve 5” storz by 5” storz,
*One 5 storz by 5 storz Humat valve
*Six 1 ½” Iowa Fallon tip pistol grip nozzles with TFT break apart mid force tip dual pressure and triple stacked tips
*One 1” Iowa Fallon tip pistol grip nozzles with TFT break apart mid force tip dual pressure and triple stacked tips
*Two 1 ½” MX tips,
*Two 1” MX tips,
*One 5/8 inch Fire Hooks Unlimited fiber glass bolt cutter
*6 foot Superior Flamefighter piercing nozzle with shutoff and two 3 foot extension pipe
*14 spare 30 minute Scott Kevlar bottles
*7 Scott 50 air packs with 30 minute Kevlar bottles and integrated PASS
*6 salvage covers to match colors (to all be blue, green and orange, one color per vehicle)
*One Hebert 5” hose clamp
*One 2 ½” screw type hydrant gate valve
*One burst hose jacket leather 2 ½” Darley
*Two misting Super Vac smoke ejectors with wheels and pull handle
*One Akron hose roller
*Two Partner 650 saws with Fire Hooks Unlimited strap, Chopper blade and Da Ax Blade, and spare fuel can for each saw. One spare each blade.
*Cordless DeWalt drill with Iowa S hook lock puller, Garage hook, Key tool set and 3/8 inch Titanium drill bit.
*One each Iowa American Rattlesnake ends polished stainless heads 6, 8, and 12 foot
*One 8 lb Force axe and pick head axe with polished stainless heads
*One Iowa American halligan with strap loop, marry strap and Iowa
*American over the shoulder strap
*One 2 ½ gallon water extinguisher with Iowa American strap
*Ansul K20E cartridge dry chemical extinguisher
All fittings to be colored(blue for one rig, red for another, green, orange, black and yellow Kochek laser etched County RFPD #1
*Four 1 1/2 inch NST female to 1 inch NST male adapters
*Two 2 ½” female NST to 1 ½” NST male
*Two 2 ½” male to 1 ½” NST female LH swivel
*Two 1 ½” NST make plugs with chains
*Five inch storz by 4 inch storz adapter
*Two 5” storz to 2 ½” LH NST swivel adapters
*25 gallons spare Class A Ansul foam
*Two Christi hydrant adapters to 5 inch storz
*Two 4 ½”??? hydrant adapters to 5 inch storz
*Two 2 ½” NST Male to 5” Storz fittings
*Two 2 ½” NST female to 5” Storz fittings
*Eleven 100 foot sections of 5” Lime Green and 11 sections of Orange 5 inch hose 100’ with three stencils each section to read at the middle and 25 foot marks plus one each yellow 25’ and 50’ sections of 5 inch hose. All fittings to be colored(Blue for one rig, red for another, green, orange, black and yellow Kochek laser etched and sequentially numbered 1 though all the 5” hose in the department.
*All strainers and suction couplings color coded as well
*Four each 5 inch storz draft gaskets, 5” storz hose gaskets, gasket for fitting, 3 inch storz draft gaskets, 2 ½”, 1 ½” and 1” hose gaskets.
*600 feet of 1 “ hose with 1” NST couplings All fittings to be colored(Blue for one rig, red for another, green, orange, black and yellow Kochek laser etched and sequentially numbered 1 though all
*High Combat 1 ¾” labeled 2” with reflective stripe 200’ yellow, 200’ green, 300’ blue, 300’ orange. All fittings to be colored(blue for one rig, red for another, green, orange, black and yellow Kochek laser etched and sequentially numbered 1 though all
*High Combat at 200’ green 2 ½” hose, all fittings to be colored(blue for one rig, red for another, green, orange, black and yellow Kochek laser etched and sequentially numbered 1 though all
*25 feet of 2 ½” hose
*Color coded everything plus stick on reflective labels with white letter and vehicle color background labels “ phone number,
*Two water throws and 60 feet of floating rope in a bag
*One Craftsman tool box with $400 worth of tools,
*Four Scotty 1 gallon garden hose Barricade gel packs
*Two 5 gallon pails of Barricade gel
*One foam can wrench
*Two long ratchet style hydrant wrenches,
*One Tracker system for 45 members and three locator devices,
*Two each long panel cutter and straight blade air chisel blades
*One package 6 and 12 inch .050 demolition blades
*10 lbs Iowa American sledge hammer
*Mount Akron fitzall and hydrant wrenches on all four sides,
*Provide 45 Cottrell storz hydrant adapters color coded to flow and main size, labeled with cable and reflective trim.
*One 5000 gallon drop tank no-frame style with dual 5” storz fittings and caps.
Warrantee
*The vendor will guarantee the lease rate at time of the order with lease to start at time of delivery..
*All apparatus to meet NFPA except where noted.
*Paint 10 years, body structure and cab 10 years, life time tank stainless body 15 years, stainless plumbing 10 years engine drive train 5 years, foam system, lifetime frame, 2 years, nozzles 5 years, hose 10 years, and pumps 5 years. Trips 4 per truck for 3 members Two hundred fifty dollar a day delivery penalty for late delivery. Delivery not to exceed 1 year. Provide 15% contingency money.
Command Rig
Ford Excursion
4x4
Diesel
Tow package
Wilburt light mast maximum lamps and wattage
Under hood generator to supply mast
Rear seat to face rear
1/3 rear seat removed to provide driver side air pack rack and turnout storage compartment
5 portable radios with chargers and 5 chargers for spare batteries
Shoreline to charge vehicle batteries
Front winch
Arrow stick rear
Cigar plugs and 110 outlets everywhere
T-pass for vehicle, repeater, portable repeater, and command box
Mount all equipment to FD desires.
Three TV’s with splitters to view 1, 2, 4 or 8 images simultaneously
Binoculars with tripod
Killer striping and warning lights
6 Grace light wands in rack
1 Bullard MX with tripod and in rig charger
Three TV cameras with broadcast ability and tripods
Gateway solo maxed out with DVD and all options, docking station, fax, copier/scanner
Water jug
Small refrigerator
Multiple radios and heads, front, middle and rear of unit
Single ear David Clarks for portables and fixed radios
Velcro tags for portables
Mount imager and TV antennas on roof
Three cell phones one each front rear and middle mounts
Blue interior lighting
Roof top IR camera and joy stick with TV built in with three head up displays and switchers for 6 units
One box lite
One Survivor light
One AIM gas detector
Alpine vehicle navigation system
Trimble vehicle GPS
Touch screen computer between driver and passenger seat
Black lite plastic work boards
Drawers and storage middle and rear
Six video recorders
Sony video camera
Nikon 35 mm camera, 28 to 300 lens, flash, camera fanny pack
Dual alternators
Upgrade battery packs
Solar chargers
Unit number on roof.
Globe command vests
Command software allowance for programming
Tribal GPS programer and antenna
CAFS Tower Ladder Hose and Air wagons
Cab and Chassis
*E-One Cyclone 8 man command cab with 7 SCBA seats, one air pack mounted between officer and rear seat for driver, 1 seat missing for rehab area. Loose one side window on each side to mount water level lights
*One full width aluminum 80” x 16” by 16” ambulance style storage in place of forward elevated windows and ambulance style sliding glass door, adjustable shelving and compartment above forward facing SCBA seats, 12 gallons of drinking water container with exterior fill and interior and exterior spigot, cup holder, 5 syrup soda dispenser gun type with syrup and carbon dioxide bottle coupled to drinking water, microwave oven, coffee maker, tea maker, refrigerator with ice maker, 110 shore line with automatic change over to AMPs generator, fill rehab area with $500 set aside no charge option to fire district This option was provided at No Charge.
* The vehicle chassis will be manufactured by the body builder.
*500 hp ISM engine with exhaust brake ands automatic transmission
*10 inch front look down mirror
*Air conditioning, describe exact air conditioning system proposed
*Car type starter switch
*In cab overhead panel to control (side dumps and chutes, Fire Research all in one combo governor instruments and pressure gauge unit, mini MC water and two foam level gauges, Akron deck gun control and remote tether mounted with velcro, Akron electric valve for gun, Elkhart deck gun controls and remote tethers mounted with velcro, spot light switch for guns, Fire Pro foam control head to default in foam when pump is engaged, pump and generator engagement switch, front, rear, officer and drivers floodlight switch), compressor switch and wet/dry switches
*Only two switches to control, siren and emergency lights,
*No head light switch,
*Ground illumination via parking brake, 12 lights
*No gauges except speedometer and fuel gauge,
*Bell and Alarm, repeater for Grace and vehicle transponder,
*Truck horn and red light system warnings connected to all visual and audible alarms on the vehicle
*6 batteries Delco model 1150
*Kussmaul pump plus 1200 with auto eject
*Headlight off on parking brake
*LED lights everywhere possible,
*7 Responder lights with chargers,
*Roof top thermal imager with dual head up displays with switching to allow either display to view the roof top imager or one handheld imager and one roof top imager or any two Bullard imagers with up to four channel worth of choices.
*XXXX model vehicle fixed radio and antenna and two XXXXX model portable radios one with a dual ear David Clark headset for the engineer, dual chargers for spare battery and radio
*Water level on/off switch,
*One quarter inch armored wheel wells front and rear and compartment undersides to protect against blown tires
*AM FM stereo with cassette player and four speakers,
*Triple frame rail,
*290 amp alternator,
*Parts book style swiveling map book holder
*One mounted Grace GEMs system with 17 transmitters, repeater, vehicle unit transmitter, 5 extra antennas, colored straps to match the unit and one command receiver, one spare battery, one portable repeater.
*Night vision blue lighting in cab
*Rear vision camera and monitor mounted on A post in cab, with back talk system
Tower
95’ E-One tower with dual remote 1500 gpm guns in basket, 3500 watts of basket flood lighting, wireless IR and TV camera with dual display boxes.
Full NFPA ground ladder compliment.
Pump
*3500 gpm Hale pump with 500 gpm hot shift pto pump for pump and roll, with shared discharge manifold.
*CAFS default on solenoid style CAFS controls with 3” Akron valve slaved to air discharges to control wet, dry or air off via single front and rear air switch. 4 CAFs deck guns midships, aerial and front and rear 3 inch supply line. No air valves, cubic foot meters, etc
*Front and rear 3 inch discharge to feed with an Akron water thief on both discharges,
*Officer side 5” LDH discharge with 5 inch by 2 ½” adapter and attached water thief,
*Side access 4” tank to pump without check valve, and 3” tank filler valve
*Garden hose wye and spigot
*Pressure relief valve
*6” side suctions with Akron piston intake valve attached to each one,
*5” storz squirrel tail side suction on each side, with wafer valves, Elkhart 5” chicksan swivels, attached to fifteen feet of 5” suction hose on one side and 3” suction hose on the other with storz coupling with Kochek foot valve low lift strainers with jets color coded to match the rigs color scheme, pull drains on each suction connection, triple primer control handles on each side to allow drafting from main pump, squirrel tail or side suction. Suction hose to be wrapped around the pump panel.
*No check valve from 4 inch tank to pump and 3 inch tank fill,
*Two Elkhart Sidewinder monitors, one located on each corner of the front bumper with CAFs tips and Collins FX-12 spot lights mounted on each gun
*All stainless steel piping,
*Auto drains as needed,
*Electric tank filler, tank to pump control on each pump panel
*Thermal relief valves with light and alarm
*Oil less primer
Fire Body
*100 inch wide body, maximum compartments available on apparatus by manufacturer.
*26 inch deep compartments Katy style with Zico overhead rack on both sides, standard doors everywhere except two front compartments that include the pump panel rollup doors and full height compartments in front of ground ladder and drop tank racks
*Raise rear body 6 inches behind rear wheels
*300 gallons poly tank total wet tank,
*101 gallon Class B tank complete with XXX foam.
*2500 feet of 5 inch hose split bed with diamond plate hose bed cover with assists and locks to hold open,
*Saulsbury custom manuals
*An extra 20 foot length of 3 and 5” high side compartment
*200 foot 3” bomb line in round bottom donut holder on officer side panel complete with TFT mini monitor with 150 to 500 gpm TFT fog tip,
*One 200 foot 1 inch preconnected line in donut roll holder with round bottom on officer’s side pump panel.
*Two 200 foot 1 ¾” labeled 2” precons on bumper round bottom,
*Two 300 foot 1 ¾” labeled 2” preconnects in donut roll holders round bottom located recessed into the rear of the apparatus with room between them for a Meyers Quick drop.
*1 remote Akron deck gun with 2” CAFs supply and 4 inch water supply with Collins FX-12 spot light mounted gun and an automatic fog tip plus tether remote on pump panel
*Dual AMPS XL units, one 25KW and one 20KW shared shaft pto generators with 90% capacity at idle in cab switches, soft start ptos no exception, with fulltime PTO’s, two forward 2000 watt Fire Research Focus, two 2000 watt Tele Lite each side and two 2000 watt Fire Research Focus rear, Wil Burt 12,000 watt night scan mast.
*1 cord light with 750 watt lights with Tele Lite base and Havis Shield head with on/off switch on the light head and 110 outlet on the front bumper attached to a manual rewind cord reel stored in dunnage area with 200 feet of cord run to the front bumper with the cord fed under the unit in tube to the bumper, reels to be attached to the generator
*2 cord lights with 750 watt lights Tele Lite base and Havis Shield head with on/off on head and outlet stored on the pump panel connected to manual rewind cord reels with 200 feet of cord in stored in the dunnage area with feed to the pump panel, reels to be attached to the generator, 3 prong 15 amp connectors on all electrical.
*Two 200 foot hydraulic reels in dunnage area connected to a 220 volt dual hydraulic pump tubed under the rig to the front bumper to supply the extrication tool with air operated on/off for each diverter valve.
*Mount all loose equipment to department desires using pullout drop down trays, pullout shelves and tool boards
*Two sets 4 water level lights 7 x 11” LED Wheelens in four colors,
*Rear Wheelen LEDs in cast bezel everywhere,
*Pool ladder to access the hose bed located at the rear of the truck,
*Rear Houston style Scotchlite,
*Wheel wells both side shall contain 12 SCBA bottles no holders,
*No rear compartments
*Reflective vehicle number plaques in drop in mounts on four sides
*Reflective department name on four sides
*New Scotchlite striping single peace no layered type allowed on stripe
*Bumper mounted Genesis spreader and cutter,
*6 bottle cascade and dual Sierra booster on turntable with dual two bottle fill station in compartment
*Three Bullard handheld imager with 4 channel transmitter 3 colors, with in vehicle charger and spare battery
Loose equipment
*Two Carlin valve 5” storz by 5” storz,
*One 5 storz by 5 storz Humat valve
*Six 1 ½” Iowa Fallon tip pistol grip nozzles with TFT break apart mid force tip dual pressure and triple stacked tips
*One 1” Iowa Fallon tip pistol grip nozzles with TFT break apart mid force tip dual pressure and triple stacked tips
*Two 1 ½” MX tips,
*Two 1” MX tips,
*One 5/8 inch Fire Hooks Unlimited fiber glass bolt cutter
*6 foot Superior Flamefighter piercing nozzle with shutoff and two 3 foot extension pipe
*14 spare 30 minute Scott Kevlar bottles
*7 Scott 50 air packs with 30 minute Kevlar bottles and integrated PASS
*6 salvage covers to match colors (to all be blue, green and orange, one color per vehicle)
*One Hebert 5” hose clamp
*One 2 ½” screw type hydrant gate valve
*One burst hose jacket leather 2 ½” Darley
*Two misting Super Vac smoke ejectors with wheels and pull handle
*One Akron hose roller
*Two Partner 650 saws with Fire Hooks Unlimited strap, Chopper blade and Da Ax Blade, and spare fuel can for each saw. One spare each blade.
*Cordless DeWalt drill with Iowa S hook lock puller, Garage hook, Key tool set and 3/8 inch Titanium drill bit.
*One each Iowa American Rattlesnake ends polished stainless heads 6, 8, and 12 foot
*One 8 lb Force axe and pick head axe with polished stainless heads
*One Iowa American halligan with strap loop, marry strap and Iowa
*American over the shoulder strap
*One 2 ½ gallon water extinguisher with Iowa American strap
*Ansul K20E cartridge dry chemical extinguisher
All fittings to be colored(blue for one rig, red for another, green, orange, black and yellow Kochek laser etched County RFPD #1
*Four 1 1/2 inch NST female to 1 inch NST male adapters
*Two 2 ½” female NST to 1 ½” NST male
*Two 2 ½” male to 1 ½” NST female LH swivel
*Two 1 ½” NST make plugs with chains
*Five inch storz by 4 inch storz adapter
*Two 5” storz to 2 ½” LH NST swivel adapters
*25 gallons spare Class A Ansul foam
*Two Christi hydrant adapters to 5 inch storz
*Two 4 ½”??? hydrant adapters to 5 inch storz
*Two 2 ½” NST Male to 5” Storz fittings
*Two 2 ½” NST female to 5” Storz fittings
*Eleven 100 foot sections of 5” Lime Green and 11 sections of Orange 5 inch hose 100’ with three stencils each section to read at the middle and 25 foot marks plus one each yellow 25’ and 50’ sections of 5 inch hose. All fittings to be colored(Blue for one rig, red for another, green, orange, black and yellow Kochek laser etched and sequentially numbered 1 though all the 5” hose in the department.
*All strainers and suction couplings color coded as well
*Four each 5 inch storz draft gaskets, 5” storz hose gaskets, gasket for fitting, 3 inch storz draft gaskets, 2 ½”, 1 ½” and 1” hose gaskets.
*600 feet of 1 “ hose with 1” NST couplings All fittings to be colored(Blue for one rig, red for another, green, orange, black and yellow Kochek laser etched and sequentially numbered 1 though all
*High Combat 1 ¾” labeled 2” with reflective stripe 200’ yellow, 200’ green, 300’ blue, 300’ orange. All fittings to be colored(blue for one rig, red for another, green, orange, black and yellow Kochek laser etched and sequentially numbered 1 though all
*High Combat at 200’ green 2 ½” hose, all fittings to be colored(blue for one rig, red for another, green, orange, black and yellow Kochek laser etched and sequentially numbered 1 though all
*25 feet of 2 ½” hose
*Color coded everything plus stick on reflective labels with white letter and vehicle color background labels “ phone number,
*Two water throws and 60 feet of floating rope in a bag
*One Craftsman tool box with $400 worth of tools,
*Four Scotty 1 gallon garden hose Barricade gel packs
*Two 5 gallon pails of Barricade gel
*One foam can wrench
*Two long ratchet style hydrant wrenches,
*One Tracker system for 45 members and three locator devices,
*Two each long panel cutter and straight blade air chisel blades
*One package 6 and 12 inch .050 demolition blades
*10 lbs Iowa American sledge hammer
*Mount Akron fitzall and hydrant wrenches on all four sides,
Warrantee
*The vendor will guarantee the lease rate at time of the order with lease to start at time of delivery..
*All apparatus to meet NFPA except where noted.
*Paint 10 years, body structure and cab 10 years, life time tank stainless body 15 years, stainless plumbing 10 years engine drive train 5 years, foam system, lifetime frame, 2 years, nozzles 5 years, hose 10 years, and pumps 5 years. Trips 4 per truck for 3 members Two hundred fifty dollar a day delivery penalty for late delivery. Delivery not to exceed 1 year. Provide 15% contingency money.
No comments:
Post a Comment